product destination |
Asynchronous motors
|
|
Quantity per set |
Set of 1
|
|
EMC filter |
Without EMC filter
|
|
type of cooling |
Integrated fan
|
|
supply frequency |
50/60 Hz +/- 5 %
|
|
communication port protocol |
Modbus
|
|
connector type |
RJ45 (on front face) for Modbus
|
|
physical interface |
2-wire RS 485 for Modbus
|
|
transmission frame |
RTU for Modbus
|
|
transmission rate |
4800 bit/s 9600 bit/s 19200 bit/s 38400 bit/s
|
|
number of addresses |
1…247 for Modbus
|
|
communication service |
Read holding registers (03) 29 words Write single register (06) 29 words Write multiple registers (16) 27 words Read/write multiple registers (23) 4/4 words Read device identification (43)
|
|
line current |
7.2 A 46.6 A
|
|
apparent power |
5.7 kVA 31.2 kVA
|
|
prospective line Isc |
5 kA 5 kA
|
|
continuous output current |
5.5 A at 4 kHz 36 A at 4 kHz
|
|
maximum transient current |
8.3 A for 60 s 39.6 A for 60 s
|
|
power dissipation in W |
66.32 W at In 517.6 W at In
|
|
speed drive output frequency |
0.5…400 Hz
|
|
nominal switching frequency |
4 kHz
|
|
switching frequency |
2...12 kHz adjustable
|
|
speed range |
1…20
|
|
transient overtorque |
170…200 % of nominal motor torque depending on drive rating and type of motor
|
|
braking torque |
Up to 150 % of nominal motor torque with braking resistor at high inertia Up to 70 % of nominal motor torque without braking resistor
|
|
asynchronous motor control profile |
Quadratic voltage/frequency ratio Energy saving ratio Sensorless flux vector control
|
|
motor slip compensation |
Preset in factory Adjustable
|
|
output voltage |
380...460 V three phase
|
|
electrical connection |
Terminal, clamping capacity: 1.5...2.5 mm² (L1, L2, L3, PA/+, PB, U, V, W)
|
|
tightening torque |
0.8…1 N.m
|
|
insulation |
Electrical between power and control
|
|
supply |
Internal supply for reference potentiometer: 5 V (4.75…5.25 V)DC, <10 mA with overload and short-circuit protection Internal supply for logic inputs: 24 V (20.4…28.8 V)DC, <100 mA with overload and short-circuit protection
|
|
analogue input number |
1
|
|
analogue input type |
Configurable current AI1 0...20 mA 250 Ohm Configurable voltage AI1 0...10 V 30 kOhm Configurable voltage AI1 0...5 V 30 kOhm
|
|
discrete input number |
4
|
|
discrete input type |
Programmable LI1...LI4 24 V 18...30 V
|
|
discrete input logic |
Negative logic (sink), > 16 V (state 0), < 10 V (state 1), input impedance 3.5 kOhm Positive logic (source), 0...< 5 V (state 0), > 11 V (state 1)
|
|
sampling duration |
10 ms for analogue input 20 ms, tolerance +/- 1 ms for logic input
|
|
linearity error |
+/- 0.3 % of maximum value for analogue input
|
|
analogue output number |
1
|
|
analogue output type |
AO1 software-configurable voltage: 0...10 V, impedance: 470 Ohm, resolution 8 bits AO1 software-configurable current: 0...20 mA, impedance: 800 Ohm, resolution 8 bits
|
|
discrete output number |
2
|
|
discrete output type |
Logic output LO+, LO- Protected relay output R1A, R1B, R1C 1 C/O
|
|
minimum switching current |
5 mA at 24 V DC for logic relay
|
|
maximum switching current |
2 A at 250 V AC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay 2 A at 30 V DC on inductive load cos phi = 0.4 L/R = 7 ms for logic relay 3 A at 250 V AC on resistive load cos phi = 1 L/R = 0 ms for logic relay 4 A at 30 V DC on resistive load cos phi = 1 L/R = 0 ms for logic relay
|
|
acceleration and deceleration ramps |
U S Linear from 0...999.9 s
|
|
braking to standstill |
By DC injection, <30 s
|
|
protection type |
Line supply overvoltage Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases Against input phase loss in three-phase Thermal motor protection via the drive by continuous calculation of I²t
|
|
frequency resolution |
Analog input: converter A/D, 10 bits Display unit: 0.1 Hz
|
|
time constant |
20 ms +/- 1 ms for reference change
|
|
operating position |
Vertical +/- 10 degree
|
|
height |
151 mm
|
|
width |
105 mm
|
|
depth |
143 mm
|
|
net weight |
1.1 kg
|
|